Ridgepoint Solutions

Blog

When to Paint a House Exterior in Austin: Temperature, Dew and Rain

The right time to paint a house exterior in Austin and surrounding Central Texas communities depends less on the month and more on the day: a dry surface, temperatures inside the range printed on the can, a surface at least 5°F above the dew point, and no rain in the forecast for the drying time the label asks for. In practice, the easier stretches are the milder weeks of spring and fall, but summer and winter jobs can go well when the work is planned around sun, dew and rain.

What temperature does exterior paint need?

Every product has its own range, and the label or technical data sheet is the rule to follow. Benjamin Moore’s temperature guide for exterior painting suggests planning for 35°F to 100°F with humidity as low as possible, and calls 77°F the ideal. Sherwin-Williams’ exterior application FAQ notes that some of its latex house paints can go on at temperatures down to 35°F, while 50°F has long been the normal minimum for latex.

The number that matters is the surface temperature, not just the air. Benjamin Moore points out that a dark wall that has sat in direct sun for a few hours can be much hotter than the air around it, and suggests checking with an infrared thermometer. If the siding is hotter than the paint’s range, wait for shade.

Is an Austin summer too hot to paint outside?

Summer is long here. The National Weather Service Austin climate summary says normal highs reach 90 degrees by late May and stay above 90 until late September, with normal highs in the upper 90s in the first half of August.

Heat is not an automatic stop, but it changes how the job runs. Sherwin-Williams warns that temperatures over 100°F can make paint dry before it bonds to the surface, which can lead to peeling later. Both manufacturers say to avoid painting in direct sun: paint that dries too fast shows lap marks and brush marks and can blister. Benjamin Moore’s exterior painting guide suggests starting on the side of the house that will stay in shade until you finish that side.

Sunlit stucco wall split by a sharp diagonal shadow, with one half in sun and one half in shade

On a summer job that usually means working each side of the house while it is out of the sun and moving around the house as the shade moves. West walls get done early, east walls later.

Why do dew and morning clouds matter so much?

Paint needs time to form a film before moisture lands on it. Benjamin Moore describes the industry standard as painting only when the surface is more than 5°F above the dew point. Sherwin-Williams says most products need at least 4 hours of dry time before moisture settles on the surface, and ideally the temperature should stay in range and above the dew point for 48 hours after application.

This is where Central Texas weather catches people. The NWS climate summary notes that low clouds often form at night and in the early morning in every season when south and southeast winds bring Gulf moisture inland, and in winter they can come with fog and drizzle. Sherwin-Williams also describes a common fall mistake: painting on a warm afternoon, then dew forms after sunset and gets into paint that has not finished curing. That can leave surface stains and weak adhesion. The fix is simple: start after the surface is truly dry, and stop early enough in the afternoon that the paint has its dry time before the evening dew.

How long should you wait to paint after rain?

Sherwin-Williams’ surface preparation page says no exterior painting should be done right after a rain, in fog or when rain is predicted. Its FAQ suggests waiting at least one day after a heavy rain, and notes that wood and masonry soak up more water than vinyl or aluminum siding. Benjamin Moore says wood should be below 15% moisture content before it is painted.

Rain timing matters in Austin. The NWS summary lists May, October and June as the wettest months, in that order, and notes that spring and summer thunderstorms can drop a lot of rain in a short time. So a mild October week can still be a poor painting week if storms keep rolling through.

If a shower hits before the paint dries and bubbles form, Benjamin Moore’s advice is to leave them alone. They may go down as the water evaporates. If they are still there after a day or two, they have to be scraped, sanded, cleaned and repainted.

Close-up of an old exterior wall with layers of blue and white paint peeling and flaking off

Can you paint the outside of a house in winter here?

Often, yes. The NWS summary lists January normal highs in the low 60s and lows in the low 40s, and, over the most recent 30-year period, an average first freeze around December 1 and last freeze around February 15. Many winter days fall inside the label range of low-temperature house paints.

The risk in winter is the cold night and the wet morning, not the afternoon. Check the overnight low against the label, give the paint its dry time before sunset, and skip days with fog or drizzle.

Does exterior painting need a permit, and what about older homes?

For one- and two-family homes and townhouses up to three stories, the City of Austin’s list of work exempt from building permits includes painting and similar finish work. Exempt work still has to meet the codes and ordinances that apply. Replacing rotted siding or trim is a separate question; see our siding page.

Homes built before 1978 may have lead-based paint under the newer coats. The EPA’s RRP rule for contractors covers paid work that disturbs paint in those homes, including painting prep. Minor work that disturbs 20 square feet or less on the exterior is not covered, though prohibited practices stay prohibited. Scraping and sanding a whole exterior is well past that line.

When you can do it yourself, and when to call a contractor

A homeowner can often handle a single-story wall, trim touch-ups or a small section of sound paint, picking a shaded, dry day and following the label. Call a contractor when the job needs tall ladders, paint is peeling across whole walls (Benjamin Moore says to find and fix the cause first), trim or siding has rot, or the house is pre-1978 and prep will disturb more than a small area. As Ridgepoint Solutions’ painting page puts it, repairs come first and paint goes on in the conditions the product allows.

Planning an exterior paint job?

Ridgepoint Solutions paints homes in Austin and surrounding Central Texas communities, with repairs, caulking and priming done before the finish coats. Get a free estimate for a walk-around and a written estimate, or email info@ridgepoint-solutions.com with a few photos of the walls and trim.

Frequently asked questions

What is the best time of year to paint a house exterior in Austin?

The milder weeks of spring and fall are usually the easiest, because the National Weather Service shows normal highs above 90 degrees from late May to late September. But the day matters more than the month. Look for a dry surface, temperatures inside the paint label’s range, a surface at least 5°F above the dew point, and no rain in the forecast for the drying time listed on the can.

Can you paint in direct sun?

Paint makers say to avoid it, especially in summer. Sun-heated siding can be much hotter than the air, and paint that dries too fast can show lap marks, blister or bond poorly. Work each side of the house while it is in shade, and check the surface temperature with an infrared thermometer if the siding is dark or has been in sun for hours.

How long does exterior paint need before rain?

Check the label first. Sherwin-Williams says most products need at least 4 hours of dry time before moisture settles on the surface, and ideally conditions stay in range and above the dew point for 48 hours. Rain on wet paint can cause bubbles. If they do not go down in a day or two, those spots need to be scraped, sanded, cleaned and repainted.

Questions about your own project?

Ask for a free estimate (737) 418-8832

← All articles

(737) 418-8832 Free estimate