Ridgepoint Solutions

Blog

Chimney Flashing Leaks: Step Flashing, Counter Flashing and Crickets in Austin

When a chimney leaks at the roof line, the flashing is the first place to look. A chimney is sealed to the roof with layers of metal: step flashing along the sides, an apron across the front, a cricket behind it on wider chimneys, and counter flashing set into the chimney that laps over all of it. If one layer is missing, loose or lapped the wrong way, water gets behind it, and caulk alone rarely fixes that for long.

Two-story house with shingle siding and dormers, with a brick chimney rising through a brown asphalt shingle roof

How is a chimney supposed to be flashed?

The Austin Residential Code (the 2024 IRC as the City of Austin adopted it) says flashing goes at every wall and roof intersection and around roof openings, and that metal flashing must be corrosion resistant and at least 0.019 inch thick. For shingle roofs, Section R905.2.8.4 says chimney flashing is installed following the shingle manufacturer’s instructions.

Owens Corning’s roofer’s installation guide lays out the usual order:

  • Front apron. A bent metal piece laps at least 4 inches over the shingles below the chimney and runs 8 to 12 inches up the chimney face.
  • Step flashing on the sides. One L-shaped piece per course of shingles, each one tucked under the next shingle up, so water steps down and out. The pieces are nailed to the roof deck only, never into the chimney.
  • Cricket flashing at the back. Metal covers the cricket and runs at least 6 inches onto the roof and at least 6 inches up the brick, lapping the side step flashing.
  • Counter flashing. A second layer is set into a mortar joint raked out about 1.5 inches, the joint is refilled with mortar, and the metal is bent down over the step and apron flashing.

The reason for two layers is movement. The same guide notes that chimneys on older homes were often built on their own foundation, so the chimney and the roof can shift at different rates. Base flashing is attached to the roof and counter flashing to the chimney, so one can slide past the other without tearing the seal.

What is a chimney cricket, and does yours need one?

A cricket, also called a saddle, is a small peaked section built on the uphill side of the chimney. Without it, water running down the roof hits the back of the chimney and sits there, along with leaves and grit. The cricket splits that water and sends it around both sides.

Under Section R903.2.2, a cricket is required on the ridge side of any chimney more than 30 inches wide, measured across the slope, and it must be covered with sheet metal or the same material as the roof. The Owens Corning guide adds that the National Roofing Contractors Association recommends one on any chimney wider than 24 inches. If your chimney is wide and the back of it shows a flat, dark, wet-looking spot or a pile of debris, a missing or undersized cricket is worth checking.

What are the signs that the flashing is the problem?

These clues point at the flashing:

  • A ceiling or wall stain right next to the chimney chase, often at a corner.
  • A leak that shows up in hard, wind-driven rain but not in light rain.
  • From the ground with binoculars: metal pulled away from the brick, a bead of caulk or roof cement in place of counter flashing, rust, or shingles that run tight against the chimney with no metal showing.
  • In the attic on a dry day: water lines or dark wood on the framing and deck around the chimney.

Austin’s storms make small gaps matter. The National Weather Service Austin climate summary calls local thunderstorms very efficient rainmakers, notes that rainfall has topped 5 inches in several hours, and says most severe weather here comes as large hail and strong winds. A burst like that finds any lap facing the wrong way. Our roof repair page covers how a leak is traced to where water actually enters, which is not always right above the stain.

Could the leak be coming from the chimney, not the flashing?

Yes. Rule it out before anyone replaces metal. Water can get in through a cracked chimney crown on top, a missing cap, or brick and mortar joints that soak up rain and let it run down inside. Those are masonry problems, and new flashing will not stop them.

Many newer homes have a framed chimney chase covered in siding or stucco instead of solid brick. On those, the code’s sidewall rule in Section R905.2.8.3 applies: base flashing at least 4 inches high and 4 inches wide, with the siding lapping over its vertical leg. Two things to check there: whether the flashing is actually tucked behind the siding or stucco, and whether the wall covering laps over it.

Does chimney flashing repair need a permit in Austin?

The City of Austin’s work exempt from building permits list does not name flashing or crickets. It does exempt asphalt shingles that replace existing asphalt shingles, and replacing any roof covering that does not adversely affect the roof structure, unless the home is in the Wildland-Urban Interface area and 50 percent or more of the roofing is being replaced. It also exempts roof decking repairs up to 128 square feet.

Exempt work still has to meet code. If the repair grows into framing a new cricket, rebuilding rotted framing or major chimney masonry work, check with Austin Development Services before the work starts. On a full reroof, the code expects flashing to be rebuilt to the manufacturer’s instructions and any rusted or damaged flashing to be replaced, not reused.

When you may not need a roofer

Some checks are simple and safe:

  • Look from the ground with binoculars and take photos of all four sides of the chimney.
  • Check the attic with a flashlight a day or two after a hard rain.
  • If the water shows up inside the firebox rather than on a ceiling or wall, start with the chimney itself.

Call a roofer when the roof is steep or two stories, the deck near the chimney feels soft, the counter flashing is just caulk, there is no cricket on a wide chimney, or the leak keeps coming back after patching. A roof inspection can sort out whether you need a flashing rebuild, masonry work or both.

Seeing a stain next to your chimney?

Ridgepoint Solutions handles residential roofing repairs for homes in Austin and surrounding Central Texas communities, including chimney flashing, crickets and the leaks around them. Get a free estimate for a look at the roof and attic, or email info@ridgepoint-solutions.com with a photo of the stain and, if you can take one safely from the ground, a photo of the chimney.

Frequently asked questions

Can caulk fix a leaking chimney flashing?

Caulk or roof cement can slow a leak for a short time, but it bakes in the sun and pulls away as the chimney and roof move. The lasting fix is metal lapped in the right order: step flashing under each shingle course, an apron at the front, cricket flashing at the back and counter flashing set into the mortar joint over all of it. Caulk is a stopgap until that work is done.

What is the difference between step flashing and counter flashing?

Step flashing is a series of small L-shaped metal pieces woven into each course of shingles along the sides of the chimney and nailed to the roof deck. Counter flashing is a second layer attached to the chimney, usually set into a mortar joint, that folds down over the step flashing. Because each layer is attached to only one side, the roof and chimney can move without breaking the seal.

Is a cricket required behind a chimney in Austin?

The Austin Residential Code requires a cricket or saddle on the ridge side of any chimney more than 30 inches wide, measured across the slope of the roof. The cricket must be covered with sheet metal or the same material as the roof. Owens Corning’s installation guide notes that the National Roofing Contractors Association recommends a cricket on chimneys wider than 24 inches.

Questions about your own project?

Ask for a free estimate (737) 418-8832

← All articles

(737) 418-8832 Free estimate